Stainless steel dishwashing station with a pre-rinse spray arm, a three-compartment sink and a dish rack under the table

Phoenix guide · 3 min read

Grease Trap Requirements For Restaurants

You have a question about a grease trap in your Phoenix kitchen. The answer is below. When you want a pump-out, ask for a call back.

The grease device is one of the few pieces of kitchen equipment that is designed by code and paid for twice if it is wrong. An undersized interceptor passes plan check, gets installed, and then fails in practice because the kitchen hits the 25 percent limit long before the city calendar. The fix is a new tank, a new permit and a new inspection.

01 / Good to know

Who decides the size

The plumbing code and the local pretreatment program decide the minimum, and an engineer or a plumber does the calculation. The inputs are the fixture count, the fixture types, the menu and the hours. A three-compartment sink, a prep sink, a mop sink, a hand sink and a dishwasher are the usual list, and the dishwasher is the fixture that changes the answer.

Tempe's program gives a simple version that is useful anywhere in the Valley: 4 or fewer kitchen fixtures on the grease line can use a hydromechanical trap, and more than 4 fixtures, or any commercial dishwasher, needs a gravity interceptor.

Water running from a wall-mounted faucet into a stainless steel sink with a round strainer drain

02 / New kitchens

The permit path

A new device or a replacement is plumbing work. It needs a permit from the city, and the inspection happens before the device is covered. In Phoenix, gravity interceptors go through the plans process, and the city publishes an approved interceptor list.

The permit package usually includes the plumbing plans, the fixture schedule, the device specification and the location. A device that is specified at 500 gallons when the calculation calls for 1,500 is a plan check comment, and a comment is cheaper than a re-installation. An existing device with a missing baffle is a grease trap repair job instead.

03 / Compare

Trap or interceptor for your concept

ConceptTypical deviceWhy
Coffee shop, no dishwasherSmall trapFew fixtures, low fat load
Cafe with a dishwasherInterceptorDishwasher trigger
Full-service restaurantInterceptor, 1,000 gallons or moreFixture count and menu
Bar with a food menuTrap or interceptorFryer load decides
Food truck commissaryInterceptor or trap per the cityWash water has to go to a device
BakeryTrap or interceptorFat load from pastry and wash

The table is a starting point, not a design. The fixture count and the menu decide.

04 / Good to know

What to set up before day one

  • The grease trap pumping schedule, with the first date on the calendar.
  • The binder: device documents, permit, service log.
  • The hauler's number and the city program's number on the cover page.
  • A scraping routine for the dish pit.
  • A rendering container for fryer oil, sized to the volume.
  • A named person who owns the FOG compliance records file.

Those 6 items take an afternoon and they prevent a common first-year problem, which is a device that was pumped but cannot be proven.

Rust-edged concrete interceptor chamber seen from above with a white tee fitting on the far wall and shallow water in the bottom

05 / New kitchens

The 3 mistakes at opening

  • 01

    Sizing to the minimum

    The minimum is a floor for a hypothetical kitchen. A real menu with a fryer and a dishwasher usually needs more.

  • 02

    Forgetting the commissary

    A food truck that washes utensils needs a commissary, and the commissary needs a device. Mesa's requirements state it directly.

  • 03

    Assuming the landlord maintains it

    Some leases put the device on the tenant. Read the clause before signing, and if it is unclear, get it in writing.

06 / Good to know

What to ask the previous tenant

If the space was a restaurant before, ask for the device size, the last 12 months of manifests and the name of the service company. If the space was not a restaurant, assume the device is new or absent and budget for one. The answer can change the build-out cost by thousands.

08 / 4 questions

Questions about opening

Still have a question?

Send the form with a short note. Someone from our team will call you back soon.

Get a call back

Q.01

Can I open with an existing device?

Yes, if it is the right size and in good condition. Get it measured and camera the line before you sign the lease.

Q.02

Who pays for the device?

The tenant or the landlord, depending on the lease. A new build usually includes it in the tenant improvement.

Q.03

How long does the permit take?

That depends on the city and the completeness of the plans. A device that is specified correctly moves faster.

Q.04

Do I need a variance?

Only if the device cannot meet the standard interval. A correctly sized device does not need one.

White vacuum service truck with a polished cylindrical stainless tank and coiled hoses parked behind a restaurant at sunset

Form open 24/7

Ask for a call back about your grease trap

Tell us which device and which kitchen. We will call you back shortly.

Thank you. You will be called back soon.

Grease backing up?Get a call back

Before you go: want a call back?

Give your name, phone number, ZIP code and the service you need. Someone will call you back about your grease trap.

Thank you. You will be called back soon.

Get a call back

Send it, and someone calls you back soon

Add details (optional)
How urgent is it?

The form is open day and night, and we will call you back shortly.

Get a call back

Send the form and someone calls you back soon.

Thank you. You will be called back soon.